Part 5 Ford Mondeo Mk3 Tddi Running Rough Crankshaft Position Sensor. In this video we change the crankshaft position sensor as this was one of the fault cod
Crankshaft position sensor. By billybear, November 17, 2020 in Ford Mondeo / Vignale Club. Followers 1. Reply to this topic. Start new topic. 1. Posted November 17, 2020. Hi new to the site I have a 2009 2.2l diesel mondeo titanium x I need to replace the crankshaft position sensor and any help with finding the location of the sensor and advice
Can anybody tell me where is the crankshaft sensor location in a 2.0 diesel (85kw)? Reply Quote 1 - 6 of 6 Posts PURPLE_2L_LX 32880 posts 路 Joined 2004 #2 路 Aug 30, 2022 Behind the crank pulley. Often worth mentioning the year of the car as quite a lot changes over the years. Facelift model changes around 2010 for example.
ellz Discussion starter 路 #5 路 Aug 26, 2020 (Edited by Moderator) ah ok, it鈥檚 on the front right corner if you鈥檙e looking at the engine. Reply. Save. Like. nicam49 路 #6 路 Aug 26, 2020 (Edited by Moderator) The map sensor is in the middle of that rigid plastic duct that's mounted on the front cross member of the front subframe. Okay, so I bit the bullet and forked out 拢75 for a genuine Ford sensor and it made absolutely no difference whatsoever , I've been told the fault could be anything from a dodgy connection in the wiring loom to an ECU fault, so have decided to cut our losses and have just part-exchanged the car against another one !!
Slackened off the tensioner and removed the bolts; pulley off. (I had replaced the belt and tensioner only 3000 miles ago so didn't change them again). Replaced the pulley wheel whilst the drive on the tensioner was tied back to the driveshaft. Got someone to stand on the brake pedal whilst torquing up the bolts. job done.
ben1191. The 2005 1.8 TDCI engine is equipped with both a timing belt and a chain. The crankshaft and diesel injection pump are connected by a chain. The diesel injection pump is connected to the camshaft by a timing belt. After 03-01-2008 Ford changed the chain which connects the crankshaft with the diesel injection pump for a so called wet belt.
Top. Re: Crankshaft Sensor Problem? amongst other things. by Altransit 禄 Tue Apr 22, 2014 10:56 pm. It could be that the engine "thinks" that it's overheating, so may just need a new temperature sensor. Another possibility is that the splines on the water pump are faulty, and it's not circulating the coolant properly.
PURPLE_2L_LX. 32895 posts 路 Joined 2004. #3 路 Oct 30, 2013. 拢600 - 拢800 generally for a complete clutch and flywheel fitted. A main dealer may charge 拢1200+. It can kill the starter motor if you leave it. Fills it with debris from the DMF. MK4.5 TDCI 140 Business Estate. . Ground. The two-wire crank position sensor has a signal cord through which the crankshaft sensor sends its voltage to the ECU. The second is the ground cord, which is necessary for the current to complete an electrical circuit. Both wires are connected to the electronic control unit. A two-wire crankshaft sensor is an inductive type sensor
Here is a picture from forscan. There are two things that seem dtange to me, first the crankshaft sensor is changing between synced, errod and synching. I would have thought it should show synched all the time when engine is running. But i get a good rpm signal all the time. Changed crankshaft and camshaft sensor but did not help.
Crankshaft sensor: large range of parts for FORD Mondeo Mk4 Hatchback (BA7) 2.0 TDCi 140 HP QXBB Free shipping from 拢 250 Crankshaft Position Sensor for FORD Mondeo Mk4 Hatchback (BA7) 2.0 TDCi 140 HP QXBB from 03.2007 ( 57 ) Suitable for a wide range of modern Ford and Mazda vehicles. Usage -- To lock and/or position camshaft, crankshafts and time belt tensioners, as well as for adjusting the VTC unit. Fitment -- Ford flesta/courier 2000, focus 1998-2000, focus 2004-2008, focus c-max 2003-2008, mondeo 2007-2008 Ford 1.8 D /TDCI These are suitable for 2.0, 2.2, 2.4 and 3.2 TDCi/TDdi Duratorq 'Puma' diesel engines in Ford Mondeo, Transit, Transit Custom and Ranger FWD, RWD and AWD vehicles. - Ensures the crankshaft position sensor is fitted in the correct position. C6R3F.
